English | 简体中文 | 繁體中文 | 한국어 | 日本語
Wednesday, 13 January 2021, 16:00 HKT/SGT
Share:
    

Source: Science and Technology of Advanced Materials
Micropillar compression for finding heat-tolerant alloys
Accurate measurements of crystalline deformation should help engineer stronger components for more energy-efficient turbines.

TSUKUBA, Japan, Jan 13, 2021 - (ACN Newswire) - Metals containing niobium silicide are promising materials that can withstand high temperatures and improve efficiency of gas turbines in power plants and aircraft. But it has been difficult to accurately determine their mechanical properties due to their complex crystal structures. Now, scientists at Kyoto University in Japan have measured what happens at the micro-level when pressure is applied on tiny samples of these materials. The approach, published in the journal Science and Technology of Advanced Materials, could help scientists obtain the accurate measurements needed to understand the atomic-level behaviour of complex crystals to develop more heat-tolerant components in gas turbines.

The scientists measured the plastic deformation that happened when a tiny probe exerted force on the micropillar specimens with various loading axis orientations.

"Our results demonstrate the cutting edge of research into plastic deformation behaviour in crystalline materials," says Kyosuke Kishida, the study's corresponding author.

Plastic deformation describes the distortion that occurs at the atomic level when a sustained force is applied to a crystal. It is difficult to measure in complex crystals. Kishida and his colleagues have been using a new approach to systematically measure plastic deformation in crystals showing promise for use in high temperature gas turbines.

In this study, they measured plastic deformation in a niobium silicide called alpha-Nb5Si3. Tiny 'micropillars' of these crystals were exposed to very small amounts of stress using a machine with a flat-punch indenter at its end. The stress was applied to different faces of the sample to determine where and how plastic deformation occurs within the crystal. By using scanning electron microscopy on the samples before and after the test, they were able to detect the planes and directions in which deformation occurred. This was followed by simulation studies based on theoretical calculations to further understand what was happening at the atomic level. Finally, the team compared the results with those of a boron-containing molybdenum silicide (Mo5SiB2) they had previously examined.

"We found that instantaneous failure occurs rather easily in alpha-Nb5Si3, which is in marked contrast to Mo5SiB2," says Kishida.

This could mean alpha-Nb5Si3 is at a disadvantage compared to Mo5SiB2 for use as a strengthening component in metal-based alloys. Kishida and his team think, however, that this material's inherent brittleness could be improved by adding other alloying elements.

The team plans to use the approach to study mechanical properties of other crystalline materials with complex structures.

Further information
Professor Kyosuke Kishida
Kyoto University
kishida.kyosuke.6w@kyoto-u.ac.jp

Paper: https://www.tandfonline.com/doi/full/10.1080/14686996.2020.1855065

About Science and Technology of Advanced Materials Journal

Open access journal STAM publishes outstanding research articles across all aspects of materials science, including functional and structural materials, theoretical analyses, and properties of materials.

Further information
Dr. Chikashi Nishimura
STAM Publishing Director
NISHIMURA.Chikashi@nims.go.jp
National Institute for Materials Science

Press release distributed by ResearchSEA for Science and Technology of Advanced Materials.

Topic: Research and development
Source: Science and Technology of Advanced Materials

Sectors: Metals & Mining, Science & Nanotech
https://www.acnnewswire.com
From the Asia Corporate News Network


Copyright © 2024 ACN Newswire. All rights reserved. A division of Asia Corporate News Network.

 

Science and Technology of Advanced Materials Related News
Dec 3, 2024 23:15 HKT/SGT
Machine learning used to optimise polymer production
Oct 25, 2024 23:00 HKT/SGT
Machine learning can predict the mechanical properties of polymers
July 30, 2024 20:00 HKT/SGT
Dual-action therapy shows promise against aggressive oral cancer
Apr 17, 2024 22:00 HKT/SGT
A new spin on materials analysis
Apr 12, 2024 18:00 HKT/SGT
Kirigami hydrogels rise from cellulose film
More news >>
Copyright © 2024 ACN Newswire - Asia Corporate News Network
Home | About us | Services | Partners | Events | Login | Contact us | Cookies Policy | Privacy Policy | Disclaimer | Terms of Use | RSS
US: +1 214 890 4418 | China: +86 181 2376 3721 | Hong Kong: +852 8192 4922 | Singapore: +65 6549 7068 | Tokyo: +81 3 6859 8575